150 واط دالي-2 & دفع DT8 يعتم 12 فولت الجهد المستمر بقيادة السائقين إمدادات الطاقة للإضاءة في الهواء الطلق
100-277vac الجهد المستمر دالي-2 محرك LED قابل للتعتيم 150 واط 4 قنوات. يمكنها تحقيق تحكم فردي في الضوء الفردي، وتعتيم المجموعة والمشهد. يمكنه ضبط السطوع ودرجة حرارة اللون للضوء بدقة وفقًا لاحتياجات المستخدم. إنها مناسبة لتركيب واستخدام مشاريع الإضاءة LED الذكية.
تخصيص
| نموذج | سمت-JB12150V-DP2-4C | سمت-JB24150V-DP2-4C | سمت-JB36150V-DP2-4C | سمت-JB48150V-DP2-4C | |
| انتاج | | الجهد المستمر | 12 فولت (12-13.5 فولت) | 24 فولت (24-26 فولت) | 36 فولت (36-38 فولت) | 48 فولت (48-50 فولت) |
| التسامح الجهد | ± 0.5 فولت | ± 0.5 فولت | ± 0.5 فولت | ± 0.5 فولت | |
| التصنيف الحالي | 12.5 أ | 6.25 أ | 4.17 أ | 3.13 أ | |
| القوة المصنفة | 150 واط | ||||
| تنظيم الحمل | 2% | 1% | 1% | 1% | |
| مدخل | مجال الجهد الكهربائي | 100-277 فولت تيار متردد | |||
| نطاق الترددات | 47 - 63 هرتز | ||||
| عامل الطاقة (النوع) @ حمولة كاملة | PF≥0.98@120VAC PF≥0.94@277VAC (تحميل كامل) | ||||
| THD(الطباع)@ حمولة كاملة | ≥10%@120VAC؛ ≥15%@277VAC | ||||
| الكفاءة (النوع) @ حمولة كاملة | 90% @ 120 فولت تيار متردد 91% @ 277 فولت تيار متردد |
91.5%@120 فولت تيار متردد 93% @ 277 فولت تيار متردد |
91.5%@120 فولت تيار متردد 92.5%@277 فولت تيار متردد |
91.5%@120 فولت تيار متردد 92.5%@277 فولت تيار متردد |
|
| التيار المتردد (الحد الأقصى) | 1.7 أ | ||||
| استهلاك الطاقة بدون تحميل (اختياري) |
1.0 واط (@120 فولت) 1.28 واط (@277 فولت) |
1.48 واط (@120 فولت) 1.76 واط (@277 فولت) |
1.52 واط (@120 فولت) 1.79 واط (@277 فولت) |
1.56 واط (@120 فولت) 1.83 واط (@277 فولت) |
|
| Standby power Consumption(optional) |
0.24W(@120V) 0.45W(@277V) |
0.24W(@120V) 0.44W(@277V) |
0.24W(@120V) 0.45W(@277V) |
0.24W(@120V) 0.47W(@277V) |
|
| Inrush Current (Typ.) | 42.4A, 50%, 496us @120VAC;68A, 50% , 380us @277VAC | ||||
| Leakage current | <0.5mA | ||||
| Protection | Short Circuit | Hiccup mode, recover automatically after fault condition is removed | |||
| Over Load | ≤120% ,hiccup mode, recover automatically after fault condition is removed | ||||
| Over temperature | case temp. over 100℃±10℃,output will be off; recovers automatically after temp. drops. | ||||
| Environ-ment | Working TEMP. | -40 ~ +70℃ (see below decrating curve) | |||
| Working Humidity | 20 ~ 95%RH,non-condensing | ||||
| Storage TEM.,Humidity | -40 ~ +80℃,10 ~ 95%RH | ||||
| TEMP.coefficient | ±0.03%/℃(0 ~ 50℃) | ||||
| Vibration | 10 ~ 500Hz, 2G 10min./1 cycle,period for 60min. each along X,Y,Z axes | ||||
| Safety & EMC | Safety standards | UL8750 UL1310 | |||
| Withstand voltage | I/P-O/P:1.80KVAC I/P-FG:1.8KVAC O/P-FG:1.8KVAC | ||||
| Isolation resistance | I/P-O/P:100MΩ/500VDC/25℃/70%RH | ||||
| EMC Emission | FCC Part 15 Subpart B | ||||
| EMC Immunity | EN61000-4-2,3,4,5,6,11 EN61547 | ||||
| Others | Net Weight | 1.05kg/pcs | |||
| Dimension | 293*125*40mm (L*W*H) | ||||
| packing | Qty: 20cs/ctn; G.W: 22.7kg/ctn; Ctn size: 330*300*215mm | ||||
| Notes | 1. All parameters NOT specially mentioned are measured at 230VAC input , rated load and 25℃of ambient temperature. | ||||
| 2. Tolerance: includes set up tolerance, line regulation and load regulation . | |||||
 |
 |
 |
 |
Mechanical Specification
※Input & Output wiring
※Input electronic cable 3*18AWG, the green cable connect with (FG) ,Black with AC (L), White with AC(N) (US);
※Output : 12V electronic cable 3*16AWG to be connected to LED Light;
24V electronic cable 3*18AWG to be connected to LED Light;
※Dimming cable
※Dimming electronic cable 3*18AWG, Brown DA/N and Purple DA/L (No polar) connected to the DALI BUS when use DALI function.
Brown (N) is connected to AC (N) while Purple (L) and pink (CCT Push )connected to CCT Push dim switch dimmer( L) when use Push function.
※Please make sure you connect these correctly otherwise your product will not function correctly and could be damaged.
CCT (TW) dimming: electronic cable, Black is output ( V+) Positive, While (CW-) and Yellow (WW-) are output (V-) negative
Note: there is external antenna at output side. Don't disassemble!
Dimming Operation
※Note: For DALI Dimming Wiring Diagram 3, please noted that only one DALI power is need in the DALI bus, so no extra DALI power is needed if the Master or Dimmer already includes the DALI Power.
Dimming Operation
※The default address for the DALI-2 LED driver is 001.
※Address settings device:
※Address settings:
① RDM setting address:
Set the address by the RDM device. For detailed operation, please refer to RDM device instruction manual.
② NFC setting address:
The DALI-2 led drivers’ address can be read and written by a mobile with NFC APP or NFC handheld device (NFC read & write device: NFC-RW) by close to the NFC signal area of the DALI-2 LED drivers.
■ Adjust output voltage Operation
※Adjust output voltage slightly for DALI-2 LED drivers
1) The driver output voltage can be read and written by a mobile with NFC APP or NFC handheld device (NFC read & write device: NFC-RW) by close to the NFC signal area of the DALI-2 LED drivers.
2) Voltage range: level 1~10, each level is 0.2V. The default output voltage level is 1.
Rated Vol. |
Level 1 |
Level 2 |
Level 3 |
Level 4 |
Level 5 |
Level 6 |
Level 7 |
Level 8 |
Level 9 |
Level 10 |
12V |
12.00V |
12.16V |
12.32V |
12.48V |
12.64V |
12.80V |
12.96V |
13.12V |
13.28V |
13.50V |
24V |
24.00V |
24.22V |
24.44V |
24.66V |
24.88V |
25.1V |
25.32V |
25.54V |
25.66V |
26.00V |
36V |
36.00V |
36.22V |
36.44V |
36.66V |
36.88V |
37.10V |
37.32V |
37.54V |
37.66V |
38.00V |
48V |
48.00V |
48.44V |
48.44V |
48.66V |
48.88V |
49.10V |
49.32V |
49.54V |
49.66V |
50.0V |
Simple operation about DALI-2 LED driver address reset and adjusting output voltage slighting by a mobile with NFC APP (set NFC) or NFC handheld device (NFC read & write device: NFC-RW)
Ø Mobilephone NFC APP setting:
Related Products
This dali-2 150W DT6 standard dimmable LED driver is integrated with the junction box for good heat dissipation. It can provide continuous and stable protection for the lamp. It has short circuit/overload/over temperature protection functions. 7-year warranty Model: SMT-JB12150V-DP2 Input Voltage: 100-277VAC Dimming Mode: DALI-2 & push Dimmable |
